Tengo un Jetta mk6 2.0L std lo acabo de comprar, le hice su servicio, le cambie aceite 5w30 el recomendado, le cambie bujías, le cambie cables de bujías, le limpie su cuerpo de aceleración, sensor MAP, válvula PCV, Pila, etc.
El carro presenta una falla un ruido en el motor, similar a cuando te arrancas en 2da y ocupaba 1era ese cascabeleo típico, pero en mayor constancia, hace ese ruido al ir en revoluciones altas, no lo hacia tan constante, hasta ayer que comenzó a incrementar la falla y el motor tiembla como si estuviera teniendo una mala mezcla, debido a eso fue que limpie cuerpo de aceler…
Leer completa
Mil Gracias.
Que costo tuvo para que no me vallan a querer sorprender
Tengo el mismo problema con mi passat, ya realice cambio de sensor map y cuerpo de aceleración, sigue presentando la falla, tú ya pediste resolver el problema. Te dejo mi correo. [email protected]
Nota: no me cobraron un solo peso. Consejo: ¡véndelo en cuanto puedas!
Otro consejo: ¡cómprate un mazda 3! jeje
http://www.profeco.gob.mx/Verificacion…
Saludos...
Model(s)
Year(s)
Engine Code
Trans. Code
VIN Range From
Vin range to
Jetta Jetta SportWagen, Golf, Golf Wagon, Passat, Beetle, Beetle Convertible
2011-2014
2.5L
(cbta, cbua)
All
All
All
01 14 23 November 17, 2014 2034012 Supersedes Technical Bulletin V011406 dated March 13, 2014 to update affected Model Years.
Update Programming, MIL ON, DTC P0106 Manifold Absolute Pressure Range / Performance Stored in ECM Fault Memory
Tip:
This software update also includes modifications for Idle control system diagnostic strategy and
DMTL system diagnostic strategy
One or more of the following fault codes may be stored in the ECM Fault Memory (Address Word 01):
Dtc
Description
P0106
Manifold Absolute Pressure Range / Performance
P0507
Idle Control System RPM Higher than Expected
P050A
Cold Start Idle Air Control System Performance
Note:
DO NOT diagnose or replace components due to P0106 fault before performing the update function as explained in this bulletin.
DO NOT diagnose or replace the throttle valve or MAP sensor before performing the update function as explained in this bulletin.
Technical Background
Monitoring strategy for the manifold absolute pressure sensor is too sensitive, causing P0106 to incorrectly set in the engine control module.
DO NOT replace any parts for this concern.
This condition as described does not affect vehicle performance or operation.
Production Solution
Improved software.
Service
Update-Programming Procedure:
Tip:
To Update-Programming using SVM, review and follow instructions in Technical Bulletin Instance 2014603 “Software Version Management”.
The SVM Process must be completed in its entirety so the database receives the update confirmation response. A warranty claim may not be reimbursed if there is no confirmation response to support the claim.
Note:
Prior to launching the ODIS service diagnostic applications and starting control module update process, confirm tester screen saber and power settings in accordance with Special Tools and Equipment - Service Information Circular # VVT-12-02. Failure to do so may result in the tester entering power sabe mode during data transfer, and subsequent control module failure.
When using a VAS 6150/X or 6160/X tester in conjunction with a VAS 5054A wireless transmitter head for a flash procedure, please connect a USB cable between the transmitter head and the tester. Failure to do so may lead to errors during the flash procedure.
VAS tools must only be used with their power adapters plugged in. Under no circumstances should they be used on battery power alone during the programming procedure.
Critical Warning: : The Midtronics Battery Charger must be connected to the vehicle battery for the duration of the programming, to ensure the battery state of charge remains above 12.5 volts during the update process. If the battery drops below 12.5 volts, the programming could fail which may result in damage to the control module. Control modules damaged by inadequate voltaje will not be covered under the warranty policy. The technician should verify the vehicle voltaje prior to starting the update process, and should monitor the voltaje for the duration of the update.
•
Update the Engine Control Module using the SVM Unit Code as listed in the table below:
Engine
Old Part #
Old Software Version
New Part #
New Software Version
Svm code
Cbua
07K 906 055 CQ
All
07K 906 055 CQ
5854
3723
Cbua
07K 906 055 DB
All
07K 906 055 DB
5855
3723
Cbta
07K 906 055 DF
All
07K 906 055 DF
5687
3723
Cbta
07K 906 055 DE
All
07K 906 055 DE
5688
3723
Cbua
07K 906 055 CP
All
07K 906 055 CP
5872
3723
Cbua
07K 906 055 CN
All
07K 906 055 CN
5873
3723
Cbta
07K 906 055 DK
All
07K 906 055 DK
5683
3723
Cbta
07K 906 055 DJ
All
07K 906 055 DJ
5684
3723
Cbua
07K 906 055 DA
All
07K 906 055 DA
5691
3723
Cbua
07K 906 055 CT
All
07K 906 055 CT
5692
3723
Cbta
07K 906 055 DH
All
07K 906 055 DH
5689
3723
Cbta
07K 906 055 DG
All
07K 906 055 DG
5690
3723
Cbua
07K 906 055 CR
All
07K 906 055 CR
5852
3723
Cbua
07K 906 055 CS
All
07K 906 055 CS
5853
3723
Cbta
07K 906 055 DD
All
07K 906 055 DD
5685
3723
Cbta
07K 906 055 DC
All
07K 906 055 DC
5686
3723
Cbua
07K 906 055 E
All
07K 906 055 E
5858
3723
Cbua
07K 906 055 D
All
07K 906 055 D
5859
3723
Cbta
07K 906 055 C
All
07K 906 055 DF
5687
3723
Cbta
07K 906 055 B
All
07K 906 055 DE
5688
3723
Cbua
07K 906 055 CJ
All
07K 906 055 CJ
5862
3723
Cbua
07K 906 055 CH
All
07K 906 055 CH
5863
3723
Cbta
07K 906 055 A
All
07K 906 055 DK
5683
3723
Cbta
07K 906 055
All
07K 906 055 DJ
5684
3723
Cbua
07K 906 055 CL
All
07K 906 055 CL
5860
3723
Cbua
07K 906 055 CK
All
07K 906 055 CK
5861
3723
Cbta
07K 906 055 BC
All
07K 906 055 DH
5689
3723
Cbta
07K 906 055 BB
All
07K 906 055 DG
5690
3723
Cbua
07K 906 055 AL
All
07K 906 055 AL
5856
3723
Cbua
07K 906 055 AK
All
07K 906 055 AK
5857
3723
Cbta
07K 906 055 AN
All
07K 906 055 DD
5685
3723
Cbta
07K 906 055 AM
All
07K 906 055 DC
5686
3723
Cbua
07K 906 055 G
All
07K 906 055 CP
5872
3723
Cbua
07K 906 055 F
All
07K 906 055 CN
5873
3723
Cbua
07K 906 055 BE
All
07K 906 055 DA
5691
3723
Cbua
07K 906 055 BD
All
07K 906 055 CT
5692
3723
The procedure can be found in GFF under Functions / Component Selection, Software Version Management, Adapting Software.
Tip:
Upon completion of software update, verify Cruise Control function (if originally equipped) is activated via GFF Function Test Plan 01 – Activate/Deactivate Cruise Control System.
Warning:
Radiator Fan(s) may cycle ON high speed during the Update Process! There is a risk that personal injury may result if contact is made with spinning fan blades.
Keep hands and all objects away from Radiator Fan(s) during Update Process!
Tip:
The SVM Process must be completed in its entirety so the database receives the update confirmation response. A warranty claim may not be reimbursed if there is no confirmation response to support the claim or action is carried out that is not explicitly stated in the Technical Bulletin.
Ensure attached ECM/TCM Tuning Form has been completed and signed by customer as required in SVM Technical Bulletin Instance 2014603.
Warranty
To determine if this procedure is covered under Warranty, always refer to the Warranty Policies and Procedures Manual 1)
Model(s)
Year(s)
Eng. Code(s)
Trans. Code(s)
VIN Range From
Vin range to
Jetta, Jetta SportWagen, Golf, Golf Wagon, Passat, Beetle, Beetle Convertible
2011-2014
2.5L
(cbta, cbua)
All
All
All
Saga coding
P0106
Manifold Absolute Pressure Range / Performance
P0507
Idle Control System RPM Higher th
Mi experiencia aquí en cdmx es terrible fui a ver central y cobraban solo por diagnóstico aunque eso ya estaba hecho, reset a los códigos de error y salió el carro como nuevo se que pasara de nuevo así que hable a otra agencia ve Iztacalco 3300 por reflasheo y lavado, seguiré buscando una agencia que no se quiera ver manchada sino de plano a Tula en un a escapada
Gracias a todos